AIR RIGS

AirRig1 AirRig2 AirRig3
1995 DAVEY KENT-DK50RA 2000 GILL BEETLE-150/C/D 1993 GILL BEETLE-B137S4D
Crawler Rotary Drill Rig, 3 1/2 reg pin down, 3 rods, 2 spd wirth head, pullmaster winch, Roper mud pump, model# PG-4, 4 cylinder diesel, air cooled, 8’6″H at lowest mast height, 53″ wide, Very god Condition. 2 extra tower sections included with rig. Serial #12693. 10′ drill rod, 4″ diameter, Cummins B3.9-P engine, 4400 ft lbs torque, 20,000 lbs pull down, 18,000 lbs pull back, 6200 hours, enclosed cab with air conditioning. Height 8’ 10”, Width 8’8”, Length 26’7”. (7) 10′ Drill Rod, Water & Oil Injection, Auxillary Controls, Power Hose Reel w/ 200 ft of 2″ Hose, A/C Cab, 353 Detroit Deisel, 3563 Hours, 3.75″ Hammer w/ 4.5″ 12 Spline Bit. 3.5” reg thread.
AirRig4 Drill(ECM590)
HYSTER-FORK DRILL 2000 ECM 590 INGERSOLL RAND
Traveling height 89″, length 10’6″, width 54″, 10′ drill rod, hammer capacity 3″ to 24″, weight 14,000 lbs., Perkins diesel powered, 9,000 lbs winch, 9,000 ft – lbs torque, 8,000 lbs pullback, table opening 24 1/4″ water injection, oil injection, 3 1/2″ Reg Thread. Self-Contained Hydraulic Drill Rig, Cummins 6CT8.3/215 HP with “on board” IR 250/140 air, 35 degree grade, 15’4″ Drifter Travel, 5 rods in Rack. Dimensions: 8’W x 9’4″H x 19’5″L x 26,000 lbs.

AUGER RIGS (Track Mounted)

AugerRig(track)1 AugerRig(track)2 AugerRig(track)3
1981 BAUER BG-7 2002 CAT 320BL W/ LODRIL 1997 SOILMEC R515J
Track Mount drill rig with O & K lower, set up for low clearance, 22,000 Gearmatic winches w/ freefall Deutz 6 cylinder diesel, Diameter up to 96”, depth 25’ 10’6”H x 30’ L x 9’w, 15’6” operating clearance, weight 65,000lbs. Track Mount drill rig with LLMHT lodril. 2 rotary torque(s) 43,000 ft lbs & 36,000 ft lbs, 40ft 2 element square locking kelly bars, up to 84” drilling diameter, 72” crowd stroke, Track Mount drill rig with low clearance setup, CAT 3306 engine, 54 ton operating weight, 154 rpm spin off, max drilling speed 26rpm, rotary head with 2 drilling speeds, telescopic kelly bar,
AugerRig(track)4 AugerRig(track)5 AugerRig(track)6
2003 Watson 1100CM 1997 Watson 3100CW WILLIAMS LDH60T
Track Mount drill rig with 8’6″ wide. 11’6″ high, 35′ long, 18′ long tracks, 35,000lbs, 1,904 hrs, 6″ outer bar, 4 1/4″ inner bar, 24″-48″ diameter, 50 depth, 41,000 ft bs torque, 18,000 lbs hoist, 23,000 lbs crowd, 40′ height. New Cables, New Hydraulic Cylinders, New Engine, Rebuilt Turntable bearing, Tilting Carbody, 11’11” Wide, Up to 96” Diameter, Up to 80’ Deep, Torque 113,00 ft lbs, Crowd 50,000, Hoist 25,000. Mounted on Pierce Pacific Tracks

AUGER RIGS (Truck Mounted)

AugerRig(truck)1 AugerRig(truck)2 AugerRig(truck)3
2002 IMT AF80 TEXOMA 650 1990 Texoma Taurus XL
IMT AF80 Hydraulic Drill Rig mounted on TOR DR8690 Carrier with Caterpillar C10 Engine with 335Hp @ 2 100rpm, 10 Speed Eaton Fuller Transmission, 8 x 6 wheel drive and a Gross Operating weight of 78 620.00 lbs.The AF80 Drill is a Caterpillar 315B Power Module with Caterpillar 3054 engine with 114 Hp @ 2100 rpm, maximum drilling torque of 60 000 ft lbs @ 7rpm, Crowd pressure of 22 500 ft lbs, Main winch pull of 20 000 ft lbs and a 3 element Kelly bar with a Digging depth of 24 meters / 78 foot. Mounted on a 2000 Peterbilt 379 Truck, 3 axles, Mounted on CCC4 axle carrier with a CAT 3406 Engine, Up to 12 ft Drilling Diameter, 120 foot depth, Cummins 6 Cyl Lower 144,000 Ft/Lbs Torque, 38,000 Lbs. Hoist, 50,000 Lbs Crowd

AugerRig(truck)4 AugerRig(truck)5 AugerRig(truck)6
2003 Watson 1100TM 1999 Schramm-450ws
Dual Rotary
1968 Williams LDH40T
Mounted on a 1988 Peterbilt 357 Truck, 3 axles One 1999 International chassis with 1999 Schramm Drill, 280’ of 4 ½” drill rod with 3 ½” reg pin, 75k truck miles, 10,500 hrs on rig, New Errickson Casing Rotator, 850/350 compressor w/ cat3406d engine. Has a Cummins 6CT engine, 7” Outer Bar, 5 ¼” Inner Bar, Full turntable w/ jacks, sliding rear jacks for 10’ drill bit clearance, Max diameter 10’, Trailer Mount

AugerRig(truck)7 AugerRig(truck)8 TBD-2
1969 Williams LDH40 1967 Williams LDH30T Williams LDH40T
Single Bar, New 6” Timkins Bar, DG Rotary, Deutz 175 hp, 6 cylinder turbo, 4 hydrualic jacks w/ extra heavy duty turtable, Mounted on 1994 CMC model C64R, 4 axles, 300HP, Jake brake, 8 low low trans, 22,000 lb front axle, 1/ 48,000 rears w/ airlift 4th axle, Very Good Condition DG rotary 7” outer bar, 5 ¼” inner bar, 6-BT Cummins upper, CAT 3306T lower, Mounted on 1976 Hendrickson Carrier Model 600-D-0H, 4 axles, w/ Hy-Rail Gear, 33’L x 13’6” H x 8’3”W, 30’ in drill position, Side reach 13’ Mounted on 2005 CCC RD10 Carrier
AugerRig(truck)10 AugerRig(truck)11 AugerRig(truck)12
1980 Williams LDH40T 1982 Williams LDH60T 1985 Williams LDH80T
8” Outer Bar, 6” inner bar, with new Deutz BMF1013c water cooled engine, Mounted on 1980 Hendrickson Carrier, Model 600-D0H, 4 axles, 290 Cummins Engine. 7” Outer Bar, 5 1/4” Inner Bar, Cummins 6BT, 175 HP, 6” Jacks, Mounted on 1982 Hendrickson Carrier Model 600-D0H, 4 axles Pressure Digger on Hendrickson carrier, Max Diameter is 96”, 6” Outer bar with 4 ¼” inner, full turntable, Air clutches, 6BT Cummins Upper, NTC350 Lower.
TBD-2
1973 Williams LDH80T
Pressure Digger on Hendrickson Carrier, Max Diameter is 96”, 6” Outer with 4 ¼” inner, Full turntable, Cummins 855 CI/255 HP lower with Road Ranger 13 Spd Transmissions, 6BT Turbo Cummins Upper with low hours, Rebuilt Final Drive.
Visit our other website
www.erricksonequipment.com
Click Here to view and print a Job Request Form.
Forms can be faxed to (908) 996-7211.
Employment Opportunities
Copyright 2015 Precision Drilling Inc.